+90 312 387 37 77 Pzt- Cmt 09:00 - 17:00 Çamlıca Mah. Anadolu Blv. TİMKO 1 İş Merkezi 20/L/4 Yenimahalle/ANKARA
1. Support water metering, power metering, time metering and multi metering.
2. One controller supports multi IC card users
3. Support relay controls output, can be directly connected to the contactor, without external relay
4. Support 4G/3G/2G, ZigBee(Option) and other type of communication
5. Support audio report of water use
Key Features
1. Data acquisition
Flow data of ultrasonic water meter, pulse water meter, and data of intelligent power meter, pulse meter, as well as pressure, water level, operation status of water pump or valve, etc.
2. Slide IC card to get water
Slide non-contact IC card to generate water pump and get water (you can set up the limited quantity of water for each IC card user)
3. Control
Support auto control, remote control water pump, valve, etc.
4. Alarm
To report alarm info if data surpasses the preset one, or lack of balance in IC card.
5. Storage
To store the data locally when power off.
6. Remote monitor
To remote monitor the devices through 4G/3G/2G cellular network.
7. Remote management
Remote configure and upgrade the devices through 4G/3G/2G cellular network.
Interfaces
| Power Requirements | |
| Standard Power | DC 12V/1.5A |
| Power Range | DC 10-28V, or AC 10-24V (DC 12V is suggested) |
| Built-in power inverting protection and over voltage protection | |
| 4-channel DIO (Digital I/O) | |
| Input Range | Low level: power active(0-3VDC), or switch on High level: power active(5-30VDC), or switch off |
| Use | For checking contactor, status of air switch and cabinet door lock |
| Built in Optical Isolation | |
| 4-channel Relay | |
| 1x Main Relay | Maximum switched voltage: 30VDC/250VAC Maximum switched current: 10A Able to connect to contactor or air switch |
| 3x Auxiliary Relay | Able to connect to contactor, air switch and Cabinet door lock |
| 4-channel Pulse Input | |
| Range | Low level: 0-2VDC High level: 2-12VDC |
| Use | Single pulse water meter and power meter Dual pulse water meter and power meter Tri-pulse water meter and power meter |
| 4-channel Analog Quantity | |
| Voltage Range | 0-5VDC |
| Current Range | 4-20ma |
| Use | To collect data from water level sensor and pressure sensor |
| 2-channel RS232 /2-channel RS485 | |
| Serial Port Rate | 300~230400bits/s |
| Data Bit | 5, 6, 7, 8 bits |
| Stop Bit | 1, 1.5, 2 bits |
| Check | No check, Even-parity Check, Odd Parity Check, SPACE and MARK check |
| Use | Connected with ultrasonic water meter and smart power meter, etc. |
| Built-in 15KV ESD protection | |
| 4-channel Power Output | |
| VCC_ADC | 12V |
| VCC_PI | 5V |
| VCC_DI | 3.3V |
| VCC_RS232 | 12V |
| VCC_RS485 | 12V |
| NFC Reader | |
| 1. Support ISO/IEC14443.2 TYPE-A Non-contact IC card 2. Range: <=5cm |
|
| LCD Screen | |
| 128*64 dot matrix, backlight | |
| 4x Keys | |
| OK, Cancel, Up and Down | |
| LED Indicators | |
| System, Alarm, Online | |
| Cellular Antenna | |
| Standard SMA female antenna interface, characteristic impedance 50Ω | |
Characteristics
| Environmental Limits | ||||
| Operating Temperature: | -40~+85ºC(-40~+185 ºF) | |||
| Ambient Relative Humidity | ≤95%, non-condensing | |||
| Power Consumption | ||||
| Work Mode | 1.2W | |||
| Note: 12V and 100mA | ||||
| Sleep Mode | 0.01W | |||
| Note: 12V and 1mA | ||||
| Anti-interference | ||||
| Type | Level | Voltage/Current Waveform | Value | |
| Power Frequency Magnetic Field | 3 | Continuous sine wave | 30A/m | |
| Damped Oscillatory Magnetic Field | 3 | Continuous sine wave | 30A/m | |
| Pulse Magnetic Field | 3 | Pulse | 100A/m | |
| Radiated Electromagnetic Field | 3 | 80MHz~1000MHz Continuous-wave | 10V/m | |
| Level 3, suitable for equipment installed in typical industrial environment: Plant, Power Plant, or residence area. | ||||
